Rabbit topiary

These are a revisited creation from years back. I made only a handful, but now that I have the process down I might make more if they end up being popular.

Friedrich certainly thinks they are handsome. :D

These are available in my etsy shop.

Categories: Flowers, plants, and trees
April 14, 2022 | 0 comments

An indispensable dispenser

A. Third hand
B. Swearing reducer
C. Masking tape dispenser
D. All of the above.

I can’t believe it has taken me so long to get one of these. :D

I’ve been swearing at minis for years trying to hold something in place while tearing off a piece of masking tape from a tape roll I can’t find, even though I just had it in my hand a moment earlier. I’m already happier having this new tool for my workspace.

Categories: Miniatures
February 27, 2022 | 0 comments

Chippendale Straight-top Highboy

One of the rarer kits in the House of Miniatures line is the Chippendale Straight-top Highboy. I love the lines of it with the flat top, and I have seen some wonderfully updated highboys in real life. A coat of paint, a change of hardware, removing the finials on the base for a cleaner look….seems like a good place to start.

There are a lot of parts, and this kit was missing only one. I can’t recall if this was a sealed kit since I had it open a bit before starting, but it’s not uncommon for these kits to have missing or extra parts even if sealed.

Some parts are harder to replace. As luck would have it, since I’ve put together other House of Miniatures kits together before and always save unused parts, I had the very part I needed! :O

I did things a little out of order in that I saved adding the legs until last. They are just too delicate to attach during the cabinet assembly. I also don’t sand cabriole legs to a perfectly round finish. I like an elephant head top with its trunk descending into a webbed duck foot. :D

I sand and fill as I go, making adjustments as needed. I added trim to the upper sides to cover the ends of the shaped top. Ends of boards never take stain the same way as a flat grain face.

To that end, I moved the corbels over slightly and needed to change the trim on the side fronts since it wasn’t wide enough to compensate for the adjustment. I cut a piece of matching trim for the top but didn’t glue it right away. I needed to address the top drawers first.

While these kits are lovely and well made, they are not always the best fitting right out of the box even if you follow the steps precisely. If you look at real life example of highboys, you will see that the drawers are not inset. They have faces that cover each hole. This would be a better look overall, but this is not how these kits are designed. The upper three drawers were the most problematic.

The upright supports dividing the three upper drawers did not align well with the actual drawer front dimensions. The supports were glued into dados, so it wasn’t something I could have prevented, but the supports also ended up crooked, which was my error. Some gaps I could live with, but this was too much.

I used a chisel to remove the original supports.

I cut new, thicker ones and set them in better position relative to the drawer widths. I first taped the drawers in relatively centered positions.

I set the new boards in place and used the drawers to fine tune.

The below picture is before I added wood filler but you can see the new dividers are already much better. Making this adjustment was going to be relatively invisible only because I planned to use black stain.

I then glued in the added trim to the top and attached the legs.

The stain I chose is Ebony by Rust-Oleum. I used a wood conditioner first, which evens out the stain application. I sanded with 600 grit between coats and buffed the finish with a paper towel before sealing with matte varnish. The dark color helps mask the gaps around the drawers and imperfections in the wood.

For hardware, I used fancy headpins. They are so-so in quality but photograph reasonably well. I will search for something to replace them eventually, so I didn’t glue them in permanently. For a kit I started in January of last year, I can finally call it done! :D

Categories: Furniture
January 23, 2022 | 0 comments

Fishy Bench

This week I assembled the Fishy Bench kit by Robin Betterley. I removed as much of the laser soot as possible and stained the wood Driftwood by Minwax.

I opted for a fabric seat cushion instead of the included artwork. I like the way it mimics the fin stripes.

This was such a fun kit to build.

Categories: Furniture
January 16, 2022 | 0 comments

Beatrix Potter vintage books

This Beatrix Potter book set from Art of Mini makes 20 books, but I have finished only 10 so far.

I love the vintage, well-loved look.

Categories: Miniatures
January 15, 2022 | 0 comments